How To Set Up A Kegerator

Kegerator Transport and Commitment Kegerators ordinarily get in via freight or ground and crave pickup from a local packet center. Most home use kegerators weigh around 100 lbs, so they are easy to lift for an average sized person with the assist of a manus truck or dolly. Free aircraft on kegerators has made online purchasing of these large appliances worthwhile.
Opening Ceremonies One time the kegerator has reached its destination, open up the pinnacle end first. Locate the back side of the kegerator and slice the cardboard open with a box pocketknife on a rear side, being careful non to hit the side walls or coils of the kegerator. Remove all of the foam packing materials and plastic wraps.
Kegerator Inspection Subsequently yous have opened up the kegerator and removed all of the packaging inside, inspect all of the walls, coils, casters, and other kegerator accessories that y'all find in the packaging for any defects or amercement. If whatsoever of your parts are damaged so you should contact the manufacturer of the kegerator immediately.
Kegerator Parts and Tools Lay out all the contents from the boxes contained in the kegerator shipping box, and so you can verify that everything you demand has been included. Read in the kegerator transmission to run into what tools you will need (philips caput screwdriver, faucet wrench) and assemble them at this signal.
Belfry Installation Locate the belfry gasket, screws and tower for assembly. Identify the gasket over the airflow hole in the top of the refrigerator until the pre-drilled screw holes line upwards. Thread the belfry beer line down through the airway hole and tighten the belfry in place making sure not to over tighten and damage the gasket.
Installing the Guardrail Place the guardrail on the vinyl or stainless steel work elevation and line up the rail over the pre-drilled screw holes. Tighten downwardly the guardrail with the provided screws, merely exist conscientious not to over tighten or y'all volition strip the screws and the guardrail with be loose and unstable.
Regulator Setup Attach the air line hose to the bottom nipple of the regulator.(Yea, we said nipple.) Make sure you take a hose clench already on and then yous can slip it up over the connection and tighten it down until firmly secure. Once again this is an area you lot do NOT want to over tighten. Over tightening here can cause a split in the line and air leaks.
Securing the co2 Tank Place the co2 tank either in its holder on the within of the kegerator or on the dorsum of the kegerator you might have an air tank holder. Tighten down the air tank or latch the tank in place. Note: The co2 tank is under a large amount of pressure level so y'all do non want information technology rolling effectually in the kegerator.
Seals and Line Clamps Locate the proper seals and clamps for attaching the beer line wing connector to the coupler. Place the seal inside the wing connection to guarantee a proper seal when dispensing draft beer out of the kegerator.
Attaching the Coupler Attach the air line (reddish) to the angled nipple on the coupler and secure with an air line clench. Next attach the beer line to the top of the coupler and secure with another line clamp of the same kind. Follow the same tightening rules every bit before.
Tap the Keg Place the coupler inside the opening of the keg and plow the coupler clockwise until it locks into place. In one case the coupler is in place printing downward on the lever to open up the keg up. See our detailed instructions on how to tap a keg.
Tightening the Faucet Catch the kegerator faucet and faucet wrench (usually provided) and insert the wrench into the holes on the faucet collar. Turn clockwise until tightened, keeping the faucet lined upwards vertical. Attach the tap handle on the threaded screw to complete the faucet assembly.
Arrange the Temperature Depending on the kegerator model yous will want to set your kegerator to reach temperatures between 34 and 38 degrees F. Virtually kegerators on the market today provide an auto-defrost characteristic which should go on the unit of measurement from freezing up, but you will want to watch how your kegerator reacts to certain temperature levels. Get a thermometer to measure the temperature if the kegerator does not accept one built-in.
Plug information technology In This is a tough one! Plug your kegerator into an outlet preferably close to a BBQ grill.
Bask Draft Beer One final step is to clean the beer lines and faucet with a kegerator cleaning kit before yous serve your start beer. In one case clean, enjoy draft beer on tap with your friends and family unit.